5115503/01INSTALLER GUIDEWe trust that these instructions give sufficient details to enable this appliance to beinstalled and maintained satisfactoril
3.10The front face of the fireplace should be reasonably flat over the area covered bythe hotbox top and side flange seals to ensure good sealing. The
in IE reference should be made to the currentedition of IS 813 “Domestic gas Installations”which makes clear the conditions that must bemet to demonst
Page 12INSTALLER GUIDEFigure 5. Appliance dimensions and clearances (Fascia may differ from that shown)(The appliance dimensions ‘A’, ‘B’ & ‘C’ sh
Page 13INSTALLER GUIDEKeyDescriptionModelBlenheim,Sonnet,HomeflameTraditional,Camden Coast AnthemQuantum MinimaDebutAura 2 FusionAAppliance height(mm
4. PACK CONTENTSRemove all the items carefully to prevent damage. Take special care when handling theceramic components. Some items may be contained i
Page 15INSTALLER GUIDEFigure 6. Pack contents continued.
5. FIREPLACE CHECK5.1 Fireplace check.5.1.1 Fireplace size The fireplace must comply with the requirements described in section 3.2. This mayentail re
exits from one terminal only and that the termination is suitable. Observe wherepossible, upstairs rooms and loft spaces for signs of escaping smoke i
Page 18INSTALLER GUIDE8. PREPARING APPLIANCE FOR INSTALLATION8.1 Appliance preparation.1. Remove any transit tape and packing andinspect for any evide
8.4 The flue restrictor.This appliance is supplied with a flue restrictorfor use where the flue draught is excessive. Therestrictor must not be fitted
Safety First.Baxi Fires Division fires are CE Approved and designed to meet the appropriate BritishStandards and Safety Marks.Quality and Excellence.A
9. HOTBOX INSTALLATION9.1 Method 1- Front fixing to fireplace surround (Not available on Blenheim,Sonnet, Homeflame Traditional, Anthem, Debut, Aura 2
Page 21applied to the cables.3. Insert a fibre wall plug into each hole. Use the fibre wall plugs supplied with thisappliance - Never use plastic plug
9.3 Floor sealing. Using the floor sealing tape supplied, seal thebottom of the hotbox to the fireplace and hearthfloor. Run the tape over the centre
10.2.1 Lighting the burner.1. Depress the control knob and rotate itanticlockwise to the ‘pilot ignition’ position. A 'click'will be heard a
10.4 Fitting the burner tray trim (This is supplied with all models but must NOTbe fitted to the Anthem model).1. Fit the burner tray trim over the fr
2. Install the fourteen loose overlay ceramiccoals as follows. The smooth surfaces of theceramic coals should be at the bottom andback. Place five of
4. Place the remaining four ceramic coals ontop of the base ceramic coal rear (See figure28).11.2 Ceramic coal fuel effect installation for the Quantu
3. Place a type “A” coal between thefront and rear base coals with theletter “A” upright and so that the coalis against the left side of the firebox(S
12. CERAMIC PEBBLES INSTALLATIONThis section is for models supplied with a ‘Pebble’ fuel effect only.For ‘Coal fuel effect’ see section 1112.1 Ceramic
4. Hold pebble ‘B’ upright with thearrow pointing to the top. Placepebble “B” on top of the base pebble.(See figure 38). 5. Hold pebble ‘C’ upright w
CONTENTSSection Heading Page1. SAFETY 42. APPLIANCE DATA 53. GENERAL INSTALLATION REQUIREMENTS 64. PACK CONTENTS 145. FIREPLACE CHECK 166. IGNITI
12.2 Ceramic pebble fuel effect installation for Fusion, Quantum, Minima andCamden models.The ceramic fuel effect may cause staining /discolouration t
4. Hold pebble ‘B’ upright withthe arrow pointing to the top.Place pebble “B” on top of thefront base pebble. The pebbleshould sit in the recess on t
10. Hold pebble ‘G’ uprightwith the arrow pointing to thetop. Place pebble “G” betweenthe front and rear base pebbles.It should lie against the side o
control knob slightly and turn back (clockwise) to turn off. This will extinguish thepilot.If the above checks are satisfactory, continue with the ins
14.2 Fitting the Quantum fascia.1. Place the fascia on top of the plinth. Be carefulnot to drag the fascia across the top surface of theplinth as this
14.4 Fitting the Blenheim, Sonnet, Homeflame Traditional, Debut & Coastfirefront.1. Place the firefront / casting on top of thehearth centrally b
14.8 Fitting the Fusion firefront.1. The Fusion firefront is secured in place using fourscrews. Locate the firefront brackets with the holes inthe bot
the appliance is installed with the flue restrictor (Seesection 8.4), remove the restrictor, reseal theappliance and retest. If smoke is still not dra
16. FINAL REVIEW1. Visually inspect the appliance. Clean off any marks incurred during installation.2. Advise the customer how to operate the fire.3.E
17. SERVICING AND PARTS REPLACEMENTAlways turn off the gas supply and allow to cool completely before commencingany servicing (The appliance inlet “T
1. SAFETYInstallerBefore continuing any further with the installation of this appliance please read thefollowing guide to manual handling:! The liftin
17.1 Checking the aeration setting of the burner.1.The aeration shutter is factory set. It is important to ensure that the aeration setting iscorrect.
17.3 To remove the pilot unit.1. Remove the burner unit (See section 17.2)2. If lying the burner on its back, ensure that the worksurface is suitably
17.5 To replace the burner. (See figure 67).1. Remove the burner unit (See section 17.2).2. Support the elbow injector and unscrew theinjector nut.3.
6. Refit the hotbox as described in the relevant installationsections. Make sure gas soundness, sealing, spillage testand performance are satisfactory
2. APPLIANCE DATAThis product uses fuel effect pieces and a burner compartment rear wallcontaining Refractory Ceramic Fibres (RCF), which are man-made
3. GENERAL INSTALLATION REQUIREMENTS3.1 The installation must be in accordance with these instructions.For the user’s protection, in the United Kingdo
and having a minimumeffective flue height of3m (10ft). A masonrychimney having acorrectly installed flueliner to BS EN 1856 Part1 or BS715 and with am
firebox (See figure 2) and it must stand on anon-combustible hearth (See figure 1).3.2.3 To a fireplace that has a precastconcrete or clay flue block
3.3.3 The flue must be completely sealedso that combustion products do not comeinto contact with combustible materialsoutside the chimney.3.3.4 The fl
Comments to this Manuals