Baxi Wentworth ClassicBaxi Kingston 2 ClassicPlease leave these instructions withthe userLive Fuel Effect Inset Gas FiresComp No 244609 - Iss 4 – 6/00
103.0 Site Requirements – Page 103.9 Gas Supply & Connection1. The gas supply is to be routed from the rear of theappliance.Turn off any applianc
114.0 Installation – Page 114.1 Initial Preparation1. Unpack the appliance from the carton and check allitems are present. The ceramic coal bed items
124.0 Installation – Page 124.2 Fitting the Fire (cont)8. Engage the tensioning nuts on the threaded shanks ofthe tensioning devices. Run the nuts do
135.0 Commissioning the Fire – Page 135.1 Checking Gas Soundness1. Turn on the gas supply and check for gas soundnesswith leak detection fluid (to BS
146.0 Arranging the Coals – Page 146.1 IdentificationIt is important that all the firebed components are usedand arranged as shown in order to achiev
156.0 Arranging the Coals – Page 156.2 Arranging the CoalbedNOTE: It is important for the safe operation of theappliance that the front and rear coal
166.0 Arranging the Coals – Page 166.3 Arranging the Loose CoalsNOTE: Due care and attention to these instructionsshould be taken when positioning the
177.0 Checking for Spillage – Page 177.1 Checking for SpillageCAUTION - Whilst checking for spillage care must betaken to avoid touching hot panels.1.
188.0 Fitting the Trim & Fender – Page 188.1 Fitting the Trim and Fender1. Carefully remove the trim and fender from theirpackaging. Place trim o
199.0 Annual Servicing – Page 199.1 MaintenanceIMPORTANT: It is possible that some soot may bedeposited on the coals after use. This is acceptablepro
2Page 2Natural GasBaxi Wentworth ClassicG.C. No 32 075 12ABaxi Kingston 2 ClassicG.C. No 32 075 18ABaxi Limited is one of the leadingmanufacturers of
209.0 Annual Servicing – Page 209.2 Preparation1. For reasons of safety and economy it is important toservice the fire annually.WARNING: Isolate the
219.0 Annual Servicing – Page 219.3 Cleaning the Burner and Injector1. Undo the screw retaining the spark electrode to theburner tray (Fig. 41).2.
229.0 Annual Servicing – Page 229.5 Cleaning the Electrode(Fig. 45 & 46)1. Check for any signs of cracking or other damage to theceramic.2. Clea
2310.0 Changing Components – Page 2310.1 Changing ComponentsWARNING: Isolate the gas supply to the appliancebefore changing any components.1. Remo
2410.0 Changing Components – Page 2410.4 Removal of Controls / Burner Chassis Assembly1. If any of the controls components are to be renewed theburn
2510.0 Changing Components – Page 2510.7 Electrode (Fig. 54 & 55)1. Disconnect the electrode lead from the tag at the baseof the electrode.2.
2610.0 Changing Components – Page 2610.9 Gas Tap and Piezo Unit (Fig. 60)1. Remove the burner as described in section 10.5.2. Undo the thermocouple
2711.0 Short parts list – Page 2711.1 Short Parts ListKeyNo.4041454422232429263019122725G.C.No.E25 213E25 214E25 218E25 217E25 198E25 199E01 617E01
3Contents - Page 3Section1.02.03.04.05.06.07.08.09.010.011.0IntroductionTechnical DataSite RequirementsInstallationCommissioning the FireArranging the
41.0 Introduction – Page 41.1 Description1. The Baxi Wentworth Classic and Kingston 2 Classic arelive fuel effect inset gas fires designed to be used
5Introduction – Page 51.3 Installation1. The appliance is suitable for installation only in G.B.and I.E. and should be installed in accordance with t
62.0 Technical Data – Page 6Kingston 2 Classic Kingston 2 ClassicCategory of Appliance 2HCategory of Appliance 2HThe fire is set for Gas Type G20
73.0 Site Requirements – Page 73.1 Site Requirements1. The Baxi Wentworth Classic and Kingston 2 Classicgas fires can be fitted to an installation wi
83.0 Site Requirements – Page 83.4 Twin Walled Metal Flue Boxes1. A double walled metal flue system conforming to theconstructional requirements of
93.0 Site Requirements – Page 93.7 Clearances (Fig. 8)1. Shelf Clearance - minimum clearance from the hearthto the underside of a combustible shelf
Comments to this Manuals